Here below you can discover a bunch of excellent tips relating to How to Install a Bathtub Yourself.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is readily obtainable, the job can move immediately; if you have to open a wall to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and embeded in the new one. Make certain you have certified on your own for the task as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is better to think about employing one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a new tub and do not require to change the plan of your previous water pipes.
Your devices and also material checklist need to make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub as well as likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait until the bathtub has actually been made use of at least once as this will certainly resolve it right into its final setting.
Planning for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, causing problems with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very serious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked the new blog entry. If you please take a moment to promote this article if you enjoyed it. Thank you so much for your time spent reading it.
Set An Appointment